Ultimaker Cura: baixar versions anteriors

New features and improvements:
- Added the new UltiMaker Factor 4+ printer, including profiles
- Added option to specify file association during the installation of Cura for windows, contributed by @hellAholic
New Settings:
- Introduced Infill Start/End Preference settings that give control over the starting location of infill
- Added Support Infill option "Lightning", and in addition the following supporting settings: Support Lightning Angle, Support Lightning Overhang Angle, Support Lightning Prune Angle, and Support Lightning Straightening Angle, which together allow you to add and control lightning infill generated for support structures
- The Support Infill Line Multiplier has been introduced to increase the quantity of infill lines. When an even number of lines is specified through this setting and paired with lightning support, it produces a single extrusion line for each island
- Introduced Minimum Hole Area in Brim Support, which filters out small holes in the support brim, resulting in a more consistent brim
- Added Temperature Delta Top Surface, which allows you to print top surfaces at a different temperature
- Added more options to Retract Before Outer Wall to give more control over retraction behavior when traveling to the outer wall
- Added Initial Layer Wall Ordering which gives control over the order in which the walls are printed for the initial layer, contributed by @hellAholic
Bug fixes:
- Support blockers now function correctly even when assigned to a disabled extruder; they no longer cause slicing conflicts and continue to effectively block support
- Fixed an issue where thin support structures would be generated within tree support
- Fixed an issue where the tree support interface layer would be missing
- Randomized infill now also works for infill skin support
- Fixed an issue where Keep or Discard profile user preference would be ignored
- Overhanging wall speed was previously applied too aggressively, resulting in extremely slow printing in overhanging areas
- Travel speed was applied to layer switches, resulting in high-speed Z-travels
- Fixed an issue where certain 3MF files would incorrectly load with an invalid setting configuration
- Fixed an issue where certain setting combinations would skip parts of the skin and walls sections
- Resolved an issue where slicing would fail when both Raft build plate adhesion and Support Lightning Infill were enabled
- Fixed an issue where overhang speed would be applied inconsistently when both Split Infill and Overhang Speed settings were enabled
- Fixed an issue where the profile has changes notification would overlap with UI elements
- Fixed an issue where certain setting configurations would cause a large amount of small line segments to be generated for the prime tower
- Fixed an issue where clicking the "Sign in to Digital Factory" button twice would fail to log in
Printer definitions, profiles and materials:
- Updated high-speed S-Line profiles to improve tree support strength and improved seam behavior by ending infill close to the seam and traveling to the seam unretracted
- Improved material detection for Method line printers to automatically select support material for the raft interface
- Automatically disable Infill Skin Support if Gradual Infill Steps is enabled, since these are conflicting settings, contributed by @hellAholic

Bug fixes:
- Fixed an issue where the export action for .makerbot file format would fail unexpectedly.

New features and improvements:
Bridging behavior over rectangular empty spaces and infill are now placed in a smarter way. The bridge lines are now anchored to layers below where possible. Bridge lines can now also be interlaced for improved quality.
Fewer mistakes, less wasted time. Settings for disabled extruders are now greyed out to prevent "ghost editing," where you might spend time fine-tuning the Printing Temperature or Retraction Distance for Extruder 2, only to realize later that the entire model was set to print with Extruder 1. Additionally, a warning appears in the Preview stage if your model is hidden because an extruder is unchecked.
- Updated combing behavior for thin parts so it doesn't ooze over the walls by updating the behavior for Inside Travel Avoid Distance
- Added a warning in the preview if the reason you are not seeing your model is that the extruder is unchecked
- Self-intersecting infills like Grid, Triangular, and Cubic are hidden for some printers in recommended mode because they introduce artifacts at high speeds. They are still available in Custom mode
- Added height of the layer in preview mode in mm in addition to the layer number, contributed by @HellAholic
- Added a pop-up to help with using the Select Face mode when rotating a model, resolves Ultimaker/Cura#21359, contributed by @HellAholic
- Improved the reliability and maintainability of the Cura UI and Post Processing plugin, contributed by @HellAholic
- Added a new button under the Help dropdown to quickly open the log files, contributed by @HellAholic
- Updated the Filament Change script of the Post Processing plugin to support multiline Gcode Before and Gcode After, contributed by @Hobbe and @GregValiant
- Updated the Z-Hop on Travel Post Processing script to include an option for Support Interface Only, contributed by @GregValiant
- Updated the Post Processing plugin with a bigger text area in the UI to allow for easier editing of multiple lines of Gcode, contributed by @HellAholic
- Updated the Advanced Cooling Fan Control Post Processing plugin to add an Enable and Fan Jump Start setting, contributed by @GregValiant
- Updated the Display Info on LCD Post Processing plugin to reflect Filament Cost and allow for the adjustment of the Cura estimated time, contributed by @GregValiant
- Updated the Purge Lines and Unload Post Processing plugin so the CUSTOM addition in the Gcode doesn't trigger an error, contributed by @GregValiant
New Settings:
New Honeycomb and Octagon infill types ensure the toolpath never crosses its own path on the same layer, reducing the chance of the nozzle hitting the infill during printing. Infill Start/End Move settings move the infill starts away from the wall to prevent surface blobs from a nozzle traveling to start a new infill line.
- Introduced Infill Start/End Move Inwards Length settings that add an extra line at the beginning and the end of your infill to prime the infill and prevent blobs on the outside wall
- Introduced Infill Skin Support to consolidate and replace Extra Infill Lines to Support Skin, Skin Edge Support Layer, and Bridging Over Infill Settings.
- Introduced a Middle option to the Z Seam Positions, contributed by @GregValiant @HellAholic
- Introduced a Print Estimation Factor to the Printer Settings that allows you to adjust the predicted printing time when you notice it deviates consistently from reality, contributed by @HellAholic
Bug fixes:
- Improved responsiveness when working with printers that are connected over Digital Factory
- Improved Scarf Seam behavior when used on overhangs and the visualization of these seams in the preview for improved troubleshooting
- Added an option to abort sending a cloud print job if the loading bar gets stuck
- Updated the behavior for One At a Time print jobs to reduce the chance of collisions at the end of the printing process
- Extruder End Gcode is now added to the end of the print process before Machine End Gcode, resolves https://github.com

UltiMaker S6 and S8 improvements:
- Introduced the CC+ 0.6 core to the UltiMaker S6 and S8. This core delivers better results for demanding applications and will be replacing the CC+ 0.4 core.
- Added new profiles for PC and CPE+ on UltiMaker S6 and S8
- Updated the default support type for the PETG material for UltiMaker S6 and S8
This release introduces print quality improvements for the UltiMaker S6 and S8 for carbon-filled printing. We intend to improve more non-engineering materials in a follow-up release.

The new UltiMaker S6 is here
Print with the new UltiMaker S6 in Cura from day 1. The UltiMaker S6 is the newest addition to the S series of UltiMaker printers that carries forward the award-winning legacy of the S5, now supercharged with innovations like the UltiMaker Cheetah for up to 4x productivity. Learn more about this printer here.

Other improvements:
- Introduced Visual Intent profiles for PLA and Tough PLA for the UltiMaker S8
- Introduced High-Speed Intents for ABSR for Method X and Method XL
Bug fixes:
- Updated UltiMaker S8 profiles to significantly improve the quality of PC, CPE, CPE+, PETG, support structures, and dual extrusion prints
- Support brims no longer listen to the Brim Distance setting, so the brims will always be attached to the support
- Fixed a bug affecting multi-extruder printers where the initial temperature was not set correctly at the start of a print if all features used an extruder other than T0

- Prime Tower Base Size
- Prime Tower Base Height
- Prime Tower Base Slope
- Prime Tower Raft Line Spacing
- Introduced the setting for Raft Line Spacing, but for the prime tower
- Updated the Support Z Distance to allow for more different values, no longer only multiple layerheights, solves #6105
- Fixed a crash for some Linux users when trying to open the file menu
- Introduced Balanced and Solid profiles for 1C extruders to UltiMaker Method X and Method XL
- Improved self-support for UltiMaker MethodX and MethodXL printers so the support extruder will not be used
- The prime tower is now always enabled when the second extruder is used for the MethodX and MethodXL printers
- Updated the default prime tower position so it doesn't prevent slicing for some printers
- Fixed an issue where raft layers were partially printed
- Slice information template variables were not available through start-end code formulas
- Resolved an issue with 100% support roof for tree support, contributed by @ThomasRahm
- Introduced Ender 3 V3 SE, contributed by @dim1triy
- Updated bridge flows for UltiMaker PLA, TPLA and ABS to address pillowing in AA 0.8 for UltiMaker printers
- Updated Spanish translation for Lightning infill, contributed by @Pelochus
- Updated German translation for Laying object flat on buildplate, contributed by @gluetolf
- Updated Brazilian translations, contributed by @Patola
- The predicted printing time for dual extrusion printjobs on the Method series are deviating from the actual printing time.
- It’s not possible yet, to use Method series printers with Digital Factory.
We hope to resolve this for the next release.

- Modify generated gcode, postprocessing it per layer
- Generate Infill patterns
- Modify extrusion paths
- Listen to a broadcast of all Settings
- Introduced Max OSX builds for ARM64 (M1 support), next to our existing X64 builds.
With major contributions from @TheSin
- Introduced a single Linux build removing the need to have a different modern and regular Linux build.
- UltiMaker printers with UltiMaker Materials have faster-predicted printing times as a result of a number of changed printing speeds
- UltiMaker configurations with limited intents in the past like AA 0.8 cores, now have more intents available
- Updated printing temperatures for UltiMaker printers to be more uniform
- Updated Support Interface Settings for UltiMaker printers
- Introduced a support material tag, so support is automatically printed with support material
- Default has been updated to Balanced to reflect the perfect harmony between these visual, engineering, and draft profiles.
- Use Tab to navigate between settings in the Per Model Settings window, solves #10967
- Introduced Ctrl-C and Ctrl-V next to the current multiply behavior, solves #8859
- Arrange your models in a grid with the same orientation with Grid Placement
- A message that shows when your Removable Disk is out of space and prevents incomplete gcodes from being saved, solves #14273
- Add Printer and Printer Settings windows are now resizable to fit in more start/end gcode in an orderly way
- Restored the color picker tool when creating custom materials, solves #11899
- You can now scroll through long messages, and can easily close them if you finished reading, solves #12325
- Searching for materials and plugins in the Cura Marketplace has been improved
- "This Setting Is Hidden Because" icons were missing in the settings visibility for Windows and Mac
- Only one file could be loaded and you could not load multiple files if they were mixed STLs and Project Files, solves #15879
- It seemed like models could be multiplied more than 99 times, there is now a limit, solves #14105
- It's now more clear if Cura is syncing materials over the cloud
- It's not possible anymore to send a printjob to a turned off cloud connected UltiMaker printer
- You can now sponsor the Cura team from the Application Switcher, and Help menu
- Infill behavior close to the skin to prevent jerky motions and visible overextrusion
- The About Dialog includes more build information for Cura developers
- Introduced more hardware info like system, release, version, processor, and CPU cores to the logging to improve troubleshooting.
- Updated supporting certify libraries
- Introduced a new Post Processing Script; Limit XY Accel for bed-slinger printers, contributed by @GregValiant
- Introduced the machine name in the gcode headers, contributed by @smartin015
- Extruder settings are cached to speed up slicing, contributed by @sesse
- The first support layers were printed incorrectly if adhesion was set to None, solves #14983
- Some improvements to the Zseam for user-specified or the sharpest corner seam alignment
- The support was printed before the brim when the origin was at the center of the buildplate, solves #14983
- Printers with a high resolution value would incorrectly print embossed features,
- The flow would unexpectedly increase after a bridge was completed.
- Bridging settings would not be applied to the first skin layer if the infill density was set to 0, solves #9056
- The skirt height could collide with some models and could be printed in support, solves #16552
- A brim would be too small if the extruder was not defined, solves #16151
- The Initial Buildplate and Printing Temperature would not be applied correctly when printing One-At-A-Time, solves #11219
- Updated some settings for UltiMaker printers to prevent infill from being exposed, introduce a visual mode for PETG, and prevent stringing for PETG and ABS
- Fixed the upgrade script for UltiMaker materials that would cause configuration errors
- Updat

- Improved slicing time for Tree Support
- Introduced 10 new settings and updated 2 so anyone can tune the behavior
- Updated options for Tree Support Rest Preference to be more correct
- Fixed a bug where Tree Support would generate unsupported islands
- Fixed a bug where slicing would fail if Preference was set to On Any Flat Surface
- Fixed a bug where branches were not generated when Support Interface was enabled.
- Fixed a bug where the Support Overhang Angle caused a crash with Tree Support
- Fixed a bug where the Support Interface was not correctly generated with Tree Support
- Updated the UltiMaker logo to reflect the new company logo
- Added support for the updated mainboard revisions of UltiMaker S3, S5, and S7
- Introduced Hole Horizontal Expansion Max Diameter so only the expansion of smaller holes can be tuned while leaving larger holes untouched.
- Introduced Skirt Height setting to make a skirt easier to remove
- Improved the minimum layer time for printers with multiple extruders.
- Improved accuracy of when the M104 Hotend Temperature command is added
- Improved printing order of the prime tower to include a dual brim, primed every layer, and primed before and after the extruder switch.
- Improved behavior for opening and closing categories when adding a new printer
- Removed the settings related to Wire Printing since it was broken and barely used.
- Upgraded PyQt to version 6.4.2 which improves responsiveness in the UI
- Fixed a bug where the brim line would not be printed in the same orientation
- Fixed a bug where models dropped to the buildplate when they were supposed to be floating
- Fixed a bug where models would overlap if multiple models were loaded at the same time
- Fixed a bug where an error would be shown too often in One At A Time print sequence
- Fixed a bug where the message for a new Beta version available would show up during the Beta.
- Fixed a bug where ESun PLA+ would display unsupported.
- Fixed a bug where the printjob name was hard to read in darkmode
- Fixed a bug where the Minimum Layer Time was incorrectly interpolated
- Fixed a bug where Cura would crash on star-up for some Linux systems because of missing SimpleButton, contributed by @fieldOfView
- Fixed a bug where the Post Processing Plugin would create extra folders, contributed by @fieldOfView
- Fixed AppImage Icon for Linux systems, contributed by @leoheck
- Fixed a bug where the buildplate temperature in the USB printing monitor was not rounded, contributed by @asteroids1975
- Fixed a bug where retracting for Filament Change was not performed correctly because of an extra /n in the gcode.
Contributed by @JuanManuelCuello
- Fixed a bug where the material estimation would not show currencies correctly.
Contributed by @Diegovd
- Fixed a bug where undesirable micro-segments would introduce jagged paths on curved surfaces.
- Fixed a bug where it was not possible to use custom support and brim meshes
- Fixed a bug Cura would not start when upgrading from a Cura 5.4 Nightly
- Fixed a bug where Connect Top/Bottom Polygons would cause a slicing crash
- Fixed a bug where generic materials were missing for some printers
- Fixed a bug where Support Horizontal Expansion would be incorrectly applied to tree supports
- Fixed a bug where nozzles were missing from the Elegoo Neptune 3 Plus.
Contributed by @GregValiant
- Introduced UltiMaker PET CF with Annealing and Engineering intents
- Updated Infill- and Skin Overlap settings for UltiMaker printers
- Enabled a modest Support Brim by default for UltiMaker printers
- Updated Support Interface speeds for PVA for UltiMaker printers
- Added Gutenberg G-Zero, contributed by @ChipCE
- Added Hellbot Magna SE 300, and Magna SE Pro, contributed by @DevelopmentHellbot
- Added Kingroon KP3S Pro, contributed by @willuhmjs
- Added LNL3D D3, D3 Vulcan, D5 and D6, contributed by @LNL3D
- Added Longer LK4 X, contributed by @BradleyFord
- Added Mixware Hyper K, Hyper S, Vulcan, and Wand, contributed by @Mi